IoT Project : Home Automation and Weather Monitor using Esp8266 Node Mcu



hello guys in this video I will show you how to make an IOT based device which can control your appliances and can monitor the temperature humidity and heat index levels so let's start it first open the re no ide and go to the tools and then go to the boards go to boards manager here you need to act the node MCU ESP 86 mod is so type here esp8266 this is the board you have to included in the ordinary so it is neatly need to be installed there I already installed it so I'm not in right now now go to these sketches be in beauty libraries so add is it gladly I given the link in the description so you can download the libraries back after totally me like let's go to the part of the library sander you need to open it since the aviary included the libraries you know I am NOT including here and not including here these are the convent require links are in the description this is the third tube you can download the freezing point in the description first take a pair board this is the an esp8266 model instance the female heritance should be MCU and fix and fix it on the third boom this is just check this side now soul of this team a hairpin the third goal now insert the male heritage decide all female and I mean take this out put some more than CMO needle now solder is amazing have an intercalary beside making today Finnegan's of the soldering it looks like this is the female DC jack this should be insert in per board and solar and you have to insert a I see some ID 0 5 500 degree we will decide this have to wire this post if I was elected to be by side I would spin off the esp8266 model and don't to the ground after connecting these you should plug this is the plastic box you may have the first set of this and Mark discarding holes now why do you lay abdomen researcher after making holes this is how the Box looks like take a swim size of cardboard and get in the box you have to make holes silicon boot now place the label inside the box and six equally to be screams here I'm taking the skills and between it now I'm fixing it you have to take a double serrated and applying down on the cardboard now place the first board over there now apply the doser tape on the top of the box for fixing the DHD level module now I am in sitting low density module is it carefully now why do you lay mode you using more ncu model as given in the circuit these are wise was behaving modules now why is the DHT level module and the connect a wife's QD esp8266 ante on you that's what it is weak like any program oh I feel good any wire no programmed according to author and programming insert it again now I am taking LEDs as control of pushing sheet of your plan book when I click on the buttons on the dashboard this is respect to the LEDs will be blow their off this we can also correct the main power supply to it who control the actual alters now testing it something the possible there now we can see the can a – we will explain yeah for the interface I am using return it for s this is the dashboard now I am clicking on switch 3 the third LEDs flown here you can see there and – and now one equal to 160 LEDs are grown and now goes to 4 before take it is also do so you can also matter the temperature levels also here you can see the – no humility compassion taking a step now I am turning rocky divided order on offseason is is I am opening of the fourth device you can see the difference on this one the sort of this whole thing – would looks like thank you for watching I hope you like and share subscribe

20 Comments

  1. Tech Maker said:

    Project in cayenne Community : https://goo.gl/zF6Bsm

    July 30, 2019
    Reply
  2. Sneha Borkar said:

    What if we want to make home automation using Arduino nodemcu relay and dht11 nd ldr sensors

    July 30, 2019
    Reply
  3. Priyank Basrani said:

    I can't find library ESP8266WiFiAP.h can u send me??

    July 30, 2019
    Reply
  4. Muhammad Waqas said:

    Dear please help me, i have uploaded the code but widgets are not appearing

    July 30, 2019
    Reply
  5. jagan said:

    Can you send me the code

    July 30, 2019
    Reply
  6. Vincent Kumar said:

    Please let me know if we can contact you for a prototype. Please email to [email protected] for us to discuss the pricing

    July 30, 2019
    Reply
  7. Amit Gupta said:

    How to make this dashboard

    July 30, 2019
    Reply
  8. Digital Home Security System said:

    plz send nu…………………….sir

    July 30, 2019
    Reply
  9. Digital Home Security System said:

    sir apke sab video bahut ache hai ap ki sikha ne ki teqnic best hai ham sikh na chah te hai plz
    my emil id [email protected] plz send u nu……… plz help me thanks? 8239309531

    July 30, 2019
    Reply
  10. Dhanush Raju said:

    How can we know whether it is connected to wifi or not

    July 30, 2019
    Reply
  11. varma vvs said:

    I can't add should I need to copy the code and paste in ide

    July 30, 2019
    Reply
  12. varma vvs said:

    I faced a error while uploading the code saying this

    Arduino: 1.8.5 (Windows 10), Board: "NodeMCU 1.0 (ESP-12E Module), 80 MHz, 4M (1M SPIFFS), v2 Prebuilt (MSS=536), Disabled, None, 115200"

    C:UsersvarmaAppDataLocalPackagesMicrosoft.MicrosoftEdge_8wekyb3d8bbweTempStateDownloadsIOT_with_Esp8266node_mcu_CayenneIOT_with_Esp8266node_mcu_Cayenne.ino:30:17: fatal error: DHT.h: No such file or directory

    #include "DHT.h"

    ^

    compilation terminated.

    exit status 1
    Error compiling for board NodeMCU 1.0 (ESP-12E Module).

    This report would have more information with
    "Show verbose output during compilation"
    option enabled in File -> Preferences.

    July 30, 2019
    Reply
  13. Dhanush Raju said:

    It can control by phone

    July 30, 2019
    Reply
  14. Akash Gupta said:

    Plz send me Cayenne dashboards link

    July 30, 2019
    Reply
  15. Dedy Isnandar said:

    Hallo TechMaker, I follow your instructions but can't make the switch/light button appear on my cayenne dashboard .. any suggest ?

    July 30, 2019
    Reply
  16. etc guy said:

    can we connect multiple sensors

    July 30, 2019
    Reply
  17. Akash Gupta said:

    Iot based home automation

    July 30, 2019
    Reply
  18. RG said:

    How about voice control? 🙂 There is my github, where you can download and try it. It is working in each language in the world.
    https://github.com/martinius96/voice-control-nodemcu
    Donate me for more interactive projects, link is on github.

    July 30, 2019
    Reply
  19. Akash Gupta said:

    I want the codings

    July 30, 2019
    Reply
  20. Amirah Azri said:

    Well done👍 sir, i would like to ask u something related to this project . Can you reply through my email [email protected] . Tq sir

    July 30, 2019
    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *